SunCoast Diesel ALTO 4L80/85E CATEGORY 1 REBUILD KIT - SC-4L80E-CAT1-A

Features and Benefits:

• NEW 4L80E OVERHAUL KIT
• ALTO RED EAGLE CLUTCH PACKS WITH INCREASED CLUTCH COUNT
• HIGH PERFORMANCE KOLENE STEELS
• UPGRADED INTERMEDIATE BAND
• NEW 4L80E FILTER
• NEW 4L80E BUSHING KIT
• NEW 4L80E THRUST WASHER KIT
• NEW LOW/REVERSE ROLLER CLUTCH
• UPGRADED 34-ELEMENT SPRAG
• UPGRADED STATOR SUPPORT BUSHING
• TORLON CHECK BALLS (10)
• UPGRADED CASE SUPPORT BUSHING
• TRIPLE DISC BILLET 258MM TORQUE CONVERTER

This Category 1 4L80E rebuild kit has several key upgrades when comparing it to our Category 0 4L80E rebuild kit to improve both performance and reliability. These upgrades include a larger 34-element intermediate sprag, new low/reverse roller, new Sonnax case bushing, torlon check balls, heavy duty Transgo separator plate and upgraded stator support bushing.

The 4L80/85E Transmission

The 4L80E (and similar 4L85E) was a series of heavy-duty transmission assemblies from GM designed for rear wheel drive configurations. The 4L80E was heavily based on the TH400 first produced in October 1963, adding electronic controls and an overdriven fourth gear. The 4L80E's were optioned only in Chevrolet/GMC pickups, 2500 Suburbans, vans, and commercial vehicles, and the Hummer H1. The 4L80E proved to be a big hit in 1991 with its release in the Silverado 454SS.

The 4L80E (RPO MT1) is rated to handle engines with up to 440 ft lb while the big brother the 4L85E (RPO MN8) is rated to handle vehicles with up to 690 ft lb.

This is a complete 4L80E super rebuild kit containing Alto Red Eagle clutches with upgraded power clutch pack that includes additional clutches and steels. The additional friction count along with the upgraded steels will improve your 4L80E's torque and horsepower capacity.

This kit will include everything else you need to rebuild your 4L80E transmission. A new filter is included as well as a bushing kit and and thrust washer kit. The band in the kit is a high performance RedEagle band.

Supporting the stator

In this SunCoast GM 4L80E transmission rebuild kit we include an upgraded Sonnax stator support bushing.

GM 4L80E and 4L85E units may display no converter lockup or codes 68, 39, 1870 or P0741. Imbalance of torque converter clutch apply oil through the front stator support bushing contributes to this complaint. A journal clearance of .002" or more will generate sufficient leakage to cause lockup clutch slippage, causing the transmission to stay in third gear. Sonnax front stator support bushing 34016-W is designed to reduce leakage by minimizing journal clearance and also increasing journal length.

Sealing Things Up

SunCoast always upgrades the check balls in all of our new 4L80E and 4L85E transmission rebuilds. In this kit you will receive 10 of these new Torlon check balls.

These new checkballs (.250") are made out of tough, wear-resistant imidized plastic. The imidized plastic balls seal better than steel balls because they conform to the separator plate ball seats. Steel checkballs are hard and heavy, wearing separator plate ball seats from the repeated high impact of the ball on the seat. Elastomer or rubber check balls seal well. However, the elastomer material wears, reducing the size of the ball. Similar imidized plastic balls have been used on some original equipment late model valve bodies with excellent results. These imidized plastic checkballs are not available through the original manufacturer.

Upgraded sprag

The intermediate sprag on the 4L80E's typically come with a 16 element intermediate sprag assembly. The can lead to failure in high horsepower and torque situations. In this 4L80E transmission rebuild kit we are upgrading the sprag to a 34 element sprag doubling the torque capacity.

A Different Plate to Serve On

On many 4L80/85E rebuilds it is not uncommon to find the factory separator plate damaged beyond repair. This is a direct result of the factory steel check balls beating the plate repeatedly.

This SunCoast 4L80E rebuild kit also has a new upgraded separator plate included with it. We use a Transgo tempered steel separator plate for longer life. This plate is custom-plated for rust resistance.

Upgraded Case Bushing

If you rebuild a lot of 4L80E's then you already know that case bushing walkout and thrust washer wear are common issues in the GM 400, 4L80E and 4L85E units. This upgraded heavy duty case bushing kit combines the tried and true no-walk case bushing with a high quality thrust bearing that replaces the OE thrust washer and selective spacer to update this area for maximum durability in all applications. Selective shims are included for setting and adjusting rear end play.

Upgraded Torque Converter

This SunCoast Category 1 4L80E transmission rebuild kit also comes complete with an upgraded triple disc billet torque converter that is available in a variety of stall speeds. This is our Pro-Loc series of SunCoast triple-disc billet torque converters.

These have a host of internal upgrades:

• Chromoly steel turbine and impeller hubs for added strength
• Fully-machined forged front billet cover
• Damperless CNC'd billet apply piston add strength and durability
• Sprag cartridge delivers more than twice the holding capacity of OE
• Weld-on pilot adapts to many applications
• Furnace-brazed and tig-welded fins
• Carbon-graphitic clutch material ensuring precise lock-up control
• Custom-modified stator assembly

This torque converter, while capable of handling the added demands of high performance vehicles, also maintains the refinement and functionality to be used in a daily driven heavy duty application such as towing. This converter can be used as a stock replacement and requires no modifications to your transmission.

The Friction Material Test

Alto Red Eagle^® material offers similar mid-point coefficient at high horsepower applications. In addition, the Alto Red Eagle® material gives superior friction wear characteristics at high energy engagements. The leading competitor's material degrades thermally and physically after reaching approximately 2.25 HP/in2.

Below we offer some engineering data collected with this particular clutch.

Six Level High Energy Test
On Frictional Properties And Wear

Lbs./Sq. Inch Pressure Required To Stop Flywheel In One Second

NOTE: The Lower Lbs./Sq.In. Required to stop the flywheel, the higher the frictional properties.

Results: Pressure required to stop the flywheel on "ALTO RED EAGLE" are slightly lower than "Manufacturer A" and well below "Manufacturer B."

Conclusion: The frictional properties of "ALTO RED EAGLE" are slightly higher than "Manufacturer A" and well above "Manufacturer B."

Test Schedule and Duration:
Test conducted in six energy levels. Each level consists of 100 clutch engagements at 60 second intervals, from 4600 RPM with a clutch lockup time of one second, the indicated pressure required to stop the flywheel in one second.